arvan et õhutama peab,seal miskid niplid paistavad kust õhutada saab.Ma arvan ega täpselt ma ei tea
| Chrysler Club Foorum http://chryslerclub.ee/foorum/ |
|
| Jahutusvedeliku vahetus http://chryslerclub.ee/foorum/viewtopic.php?f=32&t=4356 |
Leht 1 koguhulgast 1 |
| Autor: | sulev2078 [ Reede 12 Dets, 2008 12:20 ] |
| Teema pealkiri: | Jahutusvedeliku vahetus |
Operating informationist leidsin järgmise lause: Special procedures are required when filling the engine cooling system of the 2.7L Engine Kas on kellelgi infot mida nad selle "special procedures" all mõtlevad? |
|
| Autor: | valvur [ Laupäev 13 Dets, 2008 10:50 ] |
| Teema pealkiri: | |
arvan et õhutama peab,seal miskid niplid paistavad kust õhutada saab.Ma arvan ega täpselt ma ei tea
|
|
| Autor: | albert [ Laupäev 13 Dets, 2008 14:22 ] |
| Teema pealkiri: | |
COOLING SYSTEM - DRAINING When servicing the cooling system, it is essential that coolant does not drip onto the accessory drive belts and/or pulleys. Shield the belts with shop towels before working on the cooling system. If coolant contacts the belts or pulleys, flush both with clean water. WARNING: MAKE SURE ENGINE COOLING SYSTEM IS COOL BEFORE SERVICING. DO NOT REMOVE ANY CLAMPS OR HOSES , PRESSURE CAP, OR OPEN THE RADIATOR DRAINCOCK. WHEN THE SYSTEM IS HOT AND UNDER PRESSURE SERIOUS BURNS FROM COOLANT CAN OCCUR. (1) Position a clean collecting container under draincock location. (2) Open radiator draincock located at the lower right side of radiator. Turn draincock counterclockwise until it stops. (3) Remove coolant pressure cap and open cooling system bleed valve. (4) Raise vehicle on hoist. (5) 2.7L: Remove heater hose at heater tube located at the right front inner frame rail and direct coolant flow into container. COOLING SYSTEM - FILLING CAUTION: Do not use well water or suspect water supply in cooling system. A 50/50 mixture of the recommended ethylene glycol and distilled water is recommended. NOTE: Make sure all hoses are connected and radiator draincock is closed. FILLING - 2.7L (1) Close radiator draincock by turning clockwise. (2) Open cooling system bleed valve (Fig. 9). (3) Attach a 6.35 mm (0.250 in.) inside diameter clear hose that is 120.0 cm (48 in.) long to the bleed valve. Route the hose away from accessory drive belts and radiator fan. Position the other end of hose into a collecting container. The hose will prevent coolant from contacting accessory drive belts and other components. (4) Remove cooling system pressure cap. Attach Special Tool 8195, Filling Aid Funnel to coolant pressure container filler neck. (5) Use the supplied clip to pinch overflow hose that connects between the two chambers of the pressure container (Fig. 9). (6) Pour coolant into the larger section of Filling Aid Funnel (the smaller section of funnel is to allow air to escape). (7) Slowly continue filling until a steady stream of coolant flows from attached hose on bleed valve. (8) Close bleed valve and continue filling system to top of Filling Aid Funnel. (9) Remove clip from overflow hose. (10) Allow coolant in Filling Aid Funnel to drain into overflow chamber of pressure container. (11) Remove Special Tool 8195, Filling Aid Funnel and install pressure cap on pressure container. (12) Remove hose from bleed valve. (13) Start engine and allow to run until thermostat opens and radiator fans cycle. NOTE: The engine cooling system will push any remaining air into the pressure container within about one half hour of normal driving. As a result, a drop in coolant level in the pressure container may occur. If the engine cooling system overheats and pushes coolant into the overflow chamber of the pressure container, this coolant will be sucked back into the cooling system ONLY IF THE PRESSURE CAP IS LEFT ON THE PRESSURE CONTAINER. Removing the pressure cap breaks the vacuum path between the two chambers of the pressure container and the coolant will not return to the cooling system. (14) Shut off engine and allow it to cool down. This permits coolant to be drawn into the pressure chamber. (15) With engine COLD, observe coolant level in pressure chamber. Coolant level should be within MIN and MAX marks. Adjust coolant level as necessary. |
|
| Autor: | valvur [ Neljapäev 18 Dets, 2008 18:13 ] |
| Teema pealkiri: | |
krt ei saa nagu aru inglise keelest nii hästi,keegi miskit eestikeelset kokkuvõtet ei saaks teha w?? |
|
| Leht 1 koguhulgast 1 | Kõik kellaajad on UTC + 2 tundi [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|